【TORAY ABS AX05 X08】

价格
起订量
所在地	广东东莞	可售量 0KG

联系人：邓祝德

身份已验证

手机已验证

ꑶ둧ꉰꑶꑑꑑ

ꑑ-ꉰꠅ-ꑑ은ꠅ둧넨

手机扫码快速拨号

免费会员第15年

友铭（国际）塑胶化工有限公司

联系人：邓祝德 QQ交谈 (联系时,请说明是在全球塑胶网上看到的)

联系电话：ꑑ-ꉰꠅ-ꑑ은ꠅ둧넨

手机号码：ꑶ둧ꉰꑶꑑꑑ

公司官网： http://szdzd2005.51pla.com

所在地区：广东省东莞市

主营产品：工程塑料PA66, POM, PC, TPV,

进入店铺

产品分类

直销☆TORAY ABS AX05 X08☆

ABS主要优点:

● 1. 极好的冲击强度、尺寸稳定性好，柔韧性好，耐磨性好；

● 2. 化学稳定性好：耐水、无机盐、碱和酸类，不溶于大部分醇类和烃类溶剂，而容易溶于醛、酮、酯和某些氯代烃中；抗化学药品性、染色性好；

● 3. 电性能良好；

● 4. 成型加工和机械加工好，与372有机玻璃的熔接性良好，制成双色塑件，且可表面镀铬，喷漆处理；流动性比HIPS差一点，比PMMA、PC等好；

● 5. 有高抗冲、高耐热、阻燃、增强、透明等级别。

缺点

热变形温度较低，可燃，耐候性较差。

ABS 应用场合

汽车（仪表板，工具舱门，车轮盖，反光镜盒等），电冰箱，大强度工具（头发烘干机，搅拌器，食品加工机，割草机等），电话机壳体，打字机键盘，娱乐用车辆如高尔夫球手推车以及喷气式雪撬车等。

ABS 注塑工艺

★ 1. ABS成型收缩率约0.4-0.7%；

▲ 2. 无定形料，流动性中等，吸湿大，必须充分干燥，表面要求光泽的塑件须长时间预热干燥，条件80-90℃下3小时，材料湿度应保证小于0.1%；

★ 3. 宜取高料温，建议温度245℃，高模温，但料温过高易分解(分解温度为>270℃)，对精度较高的塑件，模温宜取50-60℃，对高光泽、耐热塑件，模温宜取60-80℃；

▲ 4. 宜取中高速度注塑；

★ 5. 如需解决夹水纹，需提高材料的流动性，采取高料温、高模温，或者改变入水位等方法；

▲ 6. 如成形耐热级或阻燃级材料，生产3-7天后模具表面会残存塑料分解物，导致模具表面发亮，需对模具及时进行清理，同时模具表面需增加排气位置。

▶ ✿ 友铭塑胶代理销售进口塑料，价格优惠，质量保证， --友铭塑胶优价批发，索取物性资料、报价表、UL报告、ROSH标准、SGS检测报告，COA出厂资料，MSDS材质证明开增值税等可与我司业务邓小姐联系，15016876678,15322946330,qq:470919720

供应ABS TORAY塑料

TYPES		PROCESSING	FEATURES
TRANSPARENT	900 352	Injection	Middle Impact Strength
	900 352A	Injection	Middle Impact Strength
	920 555	Injection	High Rigidity
	910 X01	Injection	Scratch Resistant
	912 X01	Injection	High Scratch Resistant
	A20C 333	Injection	SAN Standard
GENERAL PURPOSE ABS	100 322	Injection and Extrusion	High Impact Strength
	100 X01	Injection and Extrusion	Super High Impact Strength
	250 X10	Injection	High Flow
	500 322	Injection	High Rigidity
	532 X02	Injection	Abrasion Resistant, High Sliding
	700 314	Injection	Medium Impact Strength
	700 X01	Injection	High Flow Medium Impact
	700 SG5	Injection	Medium Impact High Gloss
	600 309	Extrusion	Extrusion
	600 X06	Extrusion	Extrusion
	600 X50	Extrusion	Extrusion, Thermoforming, High Impact Strength
	600 X52	Extrusion	Extrusion, Profile Extrusion
GLASS FIBRE REINFORCED ABS (ABSG)	100G-10	Injection	10% Glass Fibre Reinforced ABS
	100G-10T1	Injection	10% Glass Fiber Reinforced ABS, High Flow
	100G-20	Injection	20% Glass Fibre Reinforced ABS
	100G-30	Injection	30% Glass Fibre Reinforced ABS
GLASS FIBRE REINFORCED AS (ASG)	ASG-10	Injection	10% Glass Fibre Reinforced AS
	ASG-20	Injection	20% Glass Fibre Reinforced AS
	ASG-30	Injection	30% Glass Fibre Reinforced AS
HIGH HEAT ABS	420Y MH1	Injection	High Heat (DTL 88°C)
	430Y MH1	Injection	High Heat (DTL 90°C)
	440Y MH1	Injection	High Heat (DTL 92°C)
	440Y MH5	Injection	High Heat High Flow (DTL 92°C)
	450Y MH1	Injection	Medium High Heat (DTL 98°C)
	450Y MH5	Injection	Medium High Heat High Flow (DTL 98°C)
	450Y X10	Injection	Medium High Heat (DTL 95°C)
	460Y MH1	Injection	Medium High Heat (DTL 100°C)
	470Y MH1	Injection	Super High Heat (DTL 104°C)
	450G-10R	Injection	10% Glass Fiber Reinforced ABS (DTL 114°C)
	450G-20R	Injection	20% Glass Fiber Reinforced ABS (DTL 118°C)
	450G-20S	Injection	20% Glass Fiber Reinforced ABS, Super High Heat (DTL 128°C)
	450G-30R	Injection	30% Glass Fiber Reinforced ABS (DTL 121°C)
	450Y BM1	Injection	High Heat Blow Molding (DTL 101°C)
FLAME RETARDANT ABS	884 X01	Injection	0.75mm V-2, 1.5mm V-0, 2.5mm 5VA
	824V X01	Injection	0.75mm V-2, Light Resistant
	834V X01	Injection	2.0mm V-0,3.0 mm 5VA, Light Resistant
	834V X06	Injection	2.0mm V-0, 3.0mm 5VA, Light Resistant
	844V X05	Injection	1.5mm V-0, 2.5 mm 5VA, 2.0mm 5VB, Light Resistant
	855VG-20	Injection	20% Glass Fiber Reinforced ABS, 1.5mm V-0, 2.5mm 5VA
NON HALOGEN RESISTANT ABS	NH82C X01	Injection	0.75mm V-2, 3.0mm V-2
CHEMICAL RESISTANT ABS	AX05 X03	Injection	Standard
	AX05 X08	Injection	High Flow
	AX05 X32	Injection	High Rigidity
	AX84 X01	Injection	Flame Retardant, 1.5mm V-0
PAINTING ABS	100 MPM	Injection	Medium Impact Strength
	100 MPF	Injection	High Impact Strength
	100 MPJ	Injection	High Flow
	100 MPK	Injection	High Flow
	440Y X50	Injection	High Heat Painting (DTL 90°C)
	450Y X50	Injection	High Heat Painting (DTL 93°C)
PLATING ABS	315 X01	Injection	High Flow
	325	Injection	Standard
	335 MPL	Injection	High Flow, High Impact
ALLOY ABS	VX10G20	Injection	Glass Fiber Reinforced ABS//PBT Resin
	RFX10 X01	Injection	ABS//r-PET Alloy
	RJX2G-20	Injection	20% Glass Fiber Reinforced AS//r-PET
	RJX2G-30	Injection	30% Glass Fiber Reinforced AS//r-PET
	PX10 X06	Injection	PC//ABS Alloy, High Impact Strength
	PX10&nPCp; X07	Injection	PC//ABS Alloy, Super High Impact Strength
	RNX82	Injection	r-PC//ABS alloy, 0.75mm V-2, 3.0mm V-2
	RNX84	Injection	r-PC//ABS alloy, 1.5mm V-0
GREEN NATURAL RUBBER ABS	100N X01	Injection	Middle Impact Strength
	100N X02	Injection	Super High Impact Strength
	100N 322	Injection	High Impact Strength
	700N X02	Injection	High Flow
	335N X01	Injection	Plating
	100N MPJ	Injection	Painting