上海耀壮检测仪器设备有限公司
  • 入驻年限:5
  • 所 在 地:上海市 上海市
  • 主营产品: 仪器仪表 实验室设备 电子设备及配件 机电设备 计算机
vip

进入移动商铺

速购通标准会员第 5 vip vip vip
上海耀壮检测仪器设备有限公司
如实描述 用心服务 品质保障
딩ꥃ딩ꥃꥃ딩ꥃꉤ

荧光磁粉参考试块MTU-3磁化金属磁悬液检测试块MTU Nr.3

价格 3900.00/个
起订量 ≥1
所在地 上海 上海 可售量 10个

手机扫码快速拨号

手机扫码
速购通标准会员 第5年

上海耀壮检测仪器设备有限公司

联系电话:ꉤ딩-ꐂ딩ꥃ뤠

手机号码:딩ꥃ딩ꥃꥃ딩ꥃꉤ

公司官网: http://lutong8617888.51pla.com

所在地区:上海市 上海市

主营产品: 仪器仪表, 实验室设备, 电子设备及配件, 机电设备, 计算机,

二维码

扫一扫,加我微信

进入店铺
商品详情 联系方式

基本参数

品牌 MR 型号 MTU-3
类型 荧光磁粉悬浮液检验试块 质量认证 ISO 9934-2
执行质量标准 ISO 9934-2 产地 德国

荧光磁粉参考试块MTU-3磁化金属磁悬液检测试块(MTU-3,DIN EN ISO 9934-2:2002)GB/T15822.2

说明:

参考块类型1(MTU Nr.3)

参考试块是一个有自然裂纹的环,并经过磁化处理。在试件的两个表面上,有不同宽度、长度和深度的裂纹。每个试件都有自己的裂纹结构。

不能将裂纹显示与其他试件进行比较。

磁场参考块在这些裂缝产生的杂散不同强度通量。更敏感检查媒体结果在一个更明显的迹象表明,相比迹象时低灵敏度。中央钻孔更容易处理。

使用方法:

参考块类型1根据标准EN ISO9934-2(前说明“MTU试块”)用于显示磁粉探伤灵敏度的检查和监督磁粉试剂。表面的剩余磁化参考块包含一个网络和粗细裂缝。与磁粉溶液浸泡或喷涂后,裂纹迹象评估。

应用范围:

参考块类型1浸泡或喷洒仔细检查介质混合。冗余检查介质应倒掉。然后裂纹迹象都被视为适当的照明条件下。然后,您应该检查的疲软迹象,因为这是在粒子敏感度的差异变得明显。

注意:

参考块类型1的裂纹迹象可能受到污染,强磁场或机械的影响。给予正确的适应症,参考块前应用的污垢,油,油脂和磁性粒子。因此,参考块,应清洗后,每个应用程序(用湿布擦拭)。参考块不应暴露在强磁场,如从MP裂纹探测器,磁化和消磁线圈,磁板,等,因为它们可能会影响到剩余场阻止通过改变磁场强度和方向。

MTU-3.jpg

Instructions:

Reference Block Type 1 (MTU Nr.3)

Description:

The reference block type 1 is a residually magnetized metal disc, where, caused by a special

treatment, a network of coarse and fine cracks had been generated. The magnetic field of the

reference block generates stray fluxes of different strength across these cracks. More sensitive

inspection media result in a more distinct indications as compared to the indications when lower

sensitivity is used. The central bore hole is made for easier handling.

Use:

The reference block type 1 according to EN ISO 9934-2 (former description "MTU test block") is

used for checking and supervision of the indication sensitivity of magnetic particle crack detection

agents. The surface of the residually magnetized reference block contains a network of coarse and

fine cracks. After dipping or spraying with the magnetic particle solution, the crack indications are

evaluated.

Application:

The reference block type 1 is immersed or carefully sprayed with the well-mixed inspection medium.

Redundant inspection medium should be drained off. Then the crack indications are to be viewed

under appropriate lighting conditions. You should then inspect the weaker indications as this is

where differences in particle sensitivity becomes obvious.

Note:

The crack indication of the reference block type 1 may be affected by contamination, strong

magnetic fields, or mechanical influences. To give correct indications, the reference block should

be free of dirt, oil, grease and magnetic particles from former applications. Therefore, the reference

block should be cleaned after each application (wipe off with a wet cloth). The reference block

should not be exposed to strong magnetic fields such as from MP crack detectors, magnetizing and

demagnetizing coils, magnetic holding plates, etc. as they may influence the residual field of the

block by altering the field strength and direction.


该企业其他产品
  • 美国Kestrel 5500风速气象仪NK5500风速风向温湿度大气压力¥3000元

  • 韩国京都KDE MP-A2BL手持式磁轭UV紫外荧光磁粉探伤仪¥4500元

  • 德国EPK公司MikroTest NI50麦考特电镀镍涂层测厚仪¥12000元

  • 美国Spectroline CM-26A/FA便携紫外观察箱/CM-26暗箱紫外分析仪¥6000元

  • 德国菲希尔Fischer DUALSCOPE MPO两用涂镀层测厚仪¥5800元

  • 美国磁通MAGNAFLUX MAGNAGLO WB655荧光磁粉浓缩液¥500元

  • 瑞典兰宝Labino Torch Light UVG2 UV-A LED手电筒式紫外线灯¥4500元

  • 美国磁通MAGNAFLUX EV6000 手持式LED黑光灯¥15000元

免责声明:以上展示的荧光磁粉参考试块MTU-3磁化金属磁悬液检测试块MTU Nr.3信息由上海耀壮检测仪器设备有限公司自行提供,内容的真实性、准确性和合法性由发布企业负责, 全球塑胶网对此不承担责任。
风险防范建议:为保障您的利益,建议优先选择速购通会员
手机版:荧光磁粉参考试块MTU-3磁化金属磁悬液检测试块MTU Nr.3
更新产品链接为:https://www.51pla.com/html/sellinfo/326/32684197.htm